Gutters | Infinite Roofing & Construction Roofing Blog

Should My Roof Have Drip Edge, and What Color Should It Be?

September 24, 2020 by Infinite Roofing 1 Comment

What is the purpose of a drip edge on a roof?

Is a drip edge necessary? We have complied a guide for all your drip edge questions for shingle roofs. Drip edges are metal flashings that are installed around the edges of a roof to control the flow of water. These metal sheet are usually in the shape of an “L,” and direct water away from the fascia and into the gutters. Without its use, water would get under the shingles causing damage in numerous places of the roof. Your local roofing contractor will tell you that is is a requirement by most building codes in North America to help protect homes from damage. As we always suggest, look for the best roofing company in your area to ensure your roofing work is done properly. Not all work is created equal.

As we stated above the main key purpose of installing drip edge is to direct water away from the fascia. Water droplets stick to one another and to the surfaces they are on, it is designed to work with gravity allowing water to be forced into the gutters. Even if a home has no gutters, water will still be forced away and not collected down the fascia or soffit cavity. Without it water would stick to the shingles, working its way underneath and causing leaks.

Wind driven rain is a serious condition in which the wind forcefully pushes water all around the roof of a home. Each layer of the roofing system is designed to keep the moisture from harming the roof’s deck, which include the shingles, underlayment’s, and ice & water. Strong winds can easily push water upwards and the drip edge must compete to keep the water out. There should be about 2-4 inches of lower flange hanging off the edge of the roof to combat wind driven rain so the roof does not become compromised.

What To Do When You Experience Wind Driven Rain Roof Leak – Roofing Contractor Sullivan IL – Central Roofing LLC

What type of materials are used?

Usually it is made from numerous types of materials such as plastics and metals, the metals must be corrosion resistant or galvanized.

Copper: Many people choose copper because of its aesthetics, it has a beautiful golden color that makes the roof pop.

Deciding on the Right Roofing - Modernize

Aluminum is a very common material used. Although it is not as strong as steel aluminum does not corrode and it is often made in many colors that match many homes.

Galvanized steel is another common material used. Galvanized steel is designed to work wither water and prevent rusting. The preferable type of steel is 24 gauge so it can withstand strong winds.

Plastic, vinyl and fiberglass can also be used but these are harder to find in some areas and are not the best suited.

Drip edge comes in three basic profiles, each profile can be called more than one name so it can be a bit confusing. The C type is in the classic L shape. This type of profile is bent in a 90 degree angle with a lower flange. Type D profile is in the shape of a T, this has a lower flange on the bottom. This type is often times called D-metal or the T style. F type is an extended version with a longer edge, this is used when installing a new over existing shingles and on the rake edges. This type is often called F style or the gutter apron.

The standard sizing of drip is sold in 10.5 foot lengths and also 8ft or sometimes smaller. The overhang length ranges from 2-5 inches, you may find other sizing in your local materials store, but smaller sizing is intended for windows and not a roof.

What color should roof it be?

If your homes trim and fascia are white your local roofing contractor will most likely recommend that the best choice is white so your home is seamless. If you have for instance gray shutters on your home and other pops of gray, then choosing a gray might look nice tying it all together. Choosing a color or any building material is personally preference.

Can you install it on existing roof?

It is most often replaced when a new roof is installed, but it is possible to replace the drip edge at any time. We would not recommend a local roofing contractor who suggests leaving the old drip edge. It is best to replace the it on an existing roof in the warmer months, shingles can become brittle in the cold and break.

Do you need to replace it when replacing the roof?

No you do not have to replace it but you should, the old drip edge is most likely “old” looking and dirty from being outside for so long. If you are making the effort to replace you roof, you should replace everything so the entire roofing system looks nice. Leaving old materials to save a few bucks isn’t worth loosing on the appearance. If you want your roof to last as long as possible, everything should be replaced when doing a re-roof.

My roof should have a drip edge or overhanging shingles right? It's like this all around the house. Luckily I rent. : Roofing

How to install:

It is installed different on the eaves and rakes, once the roof deck is prepared the drip edge will be installed before the underlayment. Always consult with your local roofing company before doing any DIY work. Your roof is the most important part of your home, look for the best roofing company in your area to be sure the job is done correctly.

Step one: If you are using a type C, you can install a furring strip which will aide in its performance. A furring edge is a strip of wood that is installed on the vertical surfaces of the house under the roofs edge. When this is installed it keeps the flower flange away from the homes siding to direct water away from the home.

Step two: First install drip edges on the eaves and placing the it down, so that the water will go into the gutters. The flange will point down and away from the roof.

Step three: Using roofing nails, nail every 12 inches, never allowing more than 12 inches without a nail. When placing it piece down, it should never over the first by an inch.

The Importance of Roof Flashing

January 7, 2020 by Infinite Roofing Leave a Comment

What is Roof Flashing?

Roof flashing provides protection for different areas of your roof and works in conjunction with your roofing material. Flashing is applied to roofing corners and valleys, as well as objects that jut out through your roof. So let’s talk about what exactly is roof flashing. How does it work? Where is it used? And the different roof flashing types such as counter flashing or step flashing.

Flashing is usually built out of metal, but it may contain steel, zinc, copper, aluminum, and even plastic or rubber. Flashing is used to keep roof components waterproof and prevent any damage. Without flashing, roof components such as the junctions between walls, dormers, or chimneys may come into contact with water which can saturate, leak, and damage the component or the structure of the house. In short, the roof flashing keeps the integrity of your home intact.

The way that flashing works is by connecting to various roofing components, and it can be overlapped and connected with one another in order to keep leaks from penetrating the roof or any of the structures on your roof. Flashing can be installed with nails, glue, and caulking in order to keep your roof waterproof.

Roof flashing installation occurs throughout your roof, including all of the following places:

Valleys and Joints – the joints found throughout your roof structure are more susceptible to penetration from water, as are roof valleys. Roof joints often aren’t watertight, and roof valleys collect more water than the rest of the roof. The roof flashing ensures that these critical areas of your roof are protected.

Roof Protrusions – If there’s anything jutting out of your roof, there should be flashing to protect it. If, for instance, you have cables that tie into a satellite that’s installed on your roof, flashing can protect the opening for the satellite cables free from water and prevent any future damage.

Drip Edging – Drip edging is flashing that is applied to the edges of roofs where there aren’t gutters. Think of drip edging as a specialized roof flashing at the edge of your roof that acts as guides to prevent water from getting behind gutters and ensure that all water is directed away from your roof.

Chimneys – Chimney flashing is necessary since water can run through and collect right at the base of a chimney. Chimney flashing should be installed at the base of your chimney to keep water from infiltrating the joint between your roof and your chimney.

Pipes – It’s likely that your roof has a few pipes that penetrate the surface of your home. For instance, you probably have drain-waste vents which keeps the pressure from building up in your plumbing. These pipes can compromise a waterproof roof if they are left unprotected. Specialized “pipe boots”, which work exactly as it sounds, can be placed around these pipes in order to protect your roof.

Kickouts – Kickout flashing is installed at the lowermost joint between your roof and your wall. The kickout flashing, also known as diverter flashing, diverts rainwater away from your wall and into your gutter to avoid any kind of saturation leaks in your roof.

If you have ever noticed that there are any leaks coming from around your chimney or vent, most likely your flashing was not installed correctly or is no longer sufficient. The main purpose of roof flashing is to protect your home from moisture & saturation. The flashing extends below your roofing and adjacent to siding to create a solid, weatherproofing seal on your home to protect you from the elements. It is also much more durable and lasts longer than trying to seal or caulk around the spaces. Before sheet products were available, builders had to use different methods to try to minimize water penetrations. These methods included angling roof shingles away from the joints, installing chimneys at the ridge, and building steps off to the sides of chimneys to divert water.

Furthermore, roof flashing is less susceptible to temperature variations. If and when the other components of your roof shift slightly, due to expansion from heat or ice, the flashing will still be able to act as a barrier from the elements. If you have any concerns or thoughts that you could be having leaks call your local roofing contractor.

Flashing also adds a clean, finished look to your roof. There are areas of roofs and exterior walls that are more susceptible to leaks and water damage such as the valleys or junctions where roof sections or walls meet. It is usually installed around structures that intersect with the roofline such as dormers, skylights, vents, and chimneys. Flashing comes in a variety of materials to accommodate the desired look for the consumer. Although you may see rubber or plastic flashing out in the market, metal flashing is the more prominent kind of flashing. One of the most common types of metal flashing material used is aluminum because it is usually the most cost-effective, durable, and weather-resistant.

Counter Flashing

For starters, counter flashing is only one type of flashing and is a technique that is used to help prevent moisture from penetrating into a home behind the vertical flange of a headwall or sidewall flashing. Pieces of metal are installed in order to prevent water from passing through a structure at its joint and ensure the water is directed away from the structure. Sometimes the material used, such as vinyl, for the exterior wall siding will be enough to serve as counter flashing itself and other times a separate element is installed. This is especially important in a structure where walls are either brick or stone. The counter flashing installation process is one of the most important parts of completing any roofing system. This type of flashing should be used in conjunction with base and step flashing, to help form a waterproof barrier.

The waterproof membrane is the first layer that is laid down before the shingles are installed, called the base flashing. This membrane not only covers the first layer of the roof but also gets turned up the nearby walls or chimneys to help with the flashing process of any joints or valleys between structures. Next, L-shaped pieces of metal, typically aluminum, are placed under each shingle that is installed next to a vertical wall. One side of the L-shaped aluminum flashing lays underneath the shingle while the other side attaches up against the side of the wall. This layer is called the step flashing.

In contrast to step flashing, the next layer is installed as a continuous strip. It is installed either behind or on top of the wall adjacent to the shingles and covers the step flashing. This final layer is called counter, cover or cap flashing and most commonly consists of aluminum or galvanized steel, but is also seen made with copper, tin or even plastic. Depending on the situation, a roof with step flashing installed could sufficient in itself when combined with vinyl siding that can double as counter flashing as long as the step flashing goes underneath it. Otherwise, counter flashing is a critical requirement for all roofs.

Counter Flashing Installation Methods

Counter flashing installation can be done using one of three techniques. The first is through-wall counter flashing, which secures the flashing material to the wall cavity and the exterior siding or masonry covers it. This type of installation is only plausible during a new construction project; otherwise, it typically proves to be cost-prohibitive.

The second technique used to install counter flashing is called surface-mount flashing. This technique attaches the flashing to the exterior siding by using a sealant, typically caulk, to seal the top of the surface-mount flashing. It’s the least expensive method of installation, however, the caulk seal will need to be monitored and eventually repaired or replaced over time because it will inevitably break down.

Reglet flashing is the compromise between through-wall and surface-mount flashing. A cut is made into the exterior masonry at a 90-degree angle and the flashing material is secured in the groove made by the 90-degree cut and bent down to run parallel the exterior masonry. Although it is a more expensive and invasive technique than the surface-mount flashing, reglet flashing does not need maintenance and will last much longer than a sealant. Because of this, reglet flashing is a more convenient, long-lasting option and is recommended over the surface-mounted flashing.

Counter Flashing at Brick Headwalls and Sidewalls

Installing headwall and sidewall flashing correctly becomes more time consuming when the exterior wall covering is brick or stone.“Time-consuming” can mean “more expensive”, which is why a lot of the counter flashing you’ll see at brick and stone walls will be incorrectly installed and will solely rely on some sort of sealant to prevent moisture intrusion. Sealant eventually dries, shrinks and cracks, leaving room for moisture intrusion and future water damage. This is why it is recommended to install regret flashing to ensure the most protection from moisture intrusion.

Step Flashing

Step flashing is an L-shaped piece of metal, typically aluminum or galvanized steel, and is used where a sloped roof intersects a vertical wall. Step flashing is interwoven with the shingles and act essentially as shingles with an unturned leg to allow a transition of the vertical drainage plane of the wall to the drainage plane of the roof. One side of the L-shaped step flashing is behind the vertical drainage plane or sealed to it with some sort of sealant and/or sheathing tape. The bottom leg of the step flashing is placed over the roof drainage plane. A critical component of the step flashing is the piece that is at the end of the slope of the roof is called the kickout flashing. This roof flashing directs water away from the adjoining wall and ensures that the step flashing is not collecting water on the surface of that wall.

Is Continuous Flashing Better Than Step Flashing?

Continuous flashing is sometimes seen where a roof meets a sidewall instead of step flashing, but in the long run, step flashing will do a better job of preventing water leaks.

Step flashing redirects the water back onto the shingle and away from valleys and joints. Even if one piece of step flashing fails, the next flashing and shingle below it start the process over again, providing a system to protect your roof from water damage. Continuous flashing against a sidewall is one way to install flashing on a roof, but it’s not the correct way. Some may think that a single piece of flashing would offer more protection than many pieces of step flashing, but it doesn’t work that way. Once even a small section of the continuous flashing fails, you’ll have a leak. Each additional rainstorm will add more water, and before you know it, you’ve got rotted wood and a roof inspector in your home.

Step flashing offers far better protection from leaks because even if a single piece of step flashing fails, the water just hits the next step of the flashing. The flashing then directs the water onto the shingle and the water drains down the roof.

Kickout Flashing

Kickout flashing which can also be called diverter flashing is a special type of flashing installed at the edge of the flashing that diverts rainwater away from the cladding and into the gutter. When your roofing contractor installs kickout flashing properly, the flashing will provide excellent protection against the penetration of water behind the exterior wall covering where the flashing ends. Kickout flashing is required regardless of the roofing material excluding brick or concrete block.

Yes, there can be several factors that can lead to rainwater intrusion, but a missing kickout flashing, in particular, often results in concentrated areas of water accumulation and potentially severe damage to exterior walls. If you happen to find saturation and possibly plant growth on the exterior siding of your home, you may have missing kickout flashing causing the water damage.

Apron Flashing

Apron flashing is the metal that covers the transition between a roof slope and a roof penetration such as a dormer or chimney. Having this flashing properly installed is crucial in protecting some of the most vulnerable areas of your roofing system.

Apron flashing is usually applied as part of the two-piece roofing system. The apron is the lower L shaped piece that replaces the normal step flashing, which covers the roofing material and extends up the vertical surface of the roof penetration. The second part of the system is something we’ve touched one, which is the counter flashing that extends parallel from the vertical surface and covers the vertical leg of the apron flashing.

The Importance

Now that you have had a breakdown of the important role that roof flashing plays when it comes to the protection of your roof, it is easy to see why it is needed on almost all roofing projects. Without roof flashing, our roofs would be much more susceptible to water damage, costing homeowners thousands of dollars in repair or replacement. So when having your next roof inspected or installed, be sure that your flashing is properly installed by your local roofing contractor to ensure the best protection for your roof.

New Year’s Roof Resolutions

January 1, 2020 by Infinite Roofing Leave a Comment

The Infinite Roofing Team is reminding homeowners and business owners of the importance of the roof over their heads. Your roof is one of the most important parts of your home or business, both aesthetically and functionally, so it makes perfect sense to keep a close eye on it to keep it in good health. We’re recommending that you add your roof to this year’s list of important New Year’s Resolutions.

Scheduling A Professional Inspection

Most homeowners and business owners are unable to spot faults on their own in a roofing system until it’s too late or until water has penetrated the surface. Therefore, by scheduling an inspection with your local roofing contractor, they can help pinpoint any potential problems before it is too late. The point of having a roofing contractor is so that they can provide a complete and thorough inspection of your roofing system. As a homeowner possibly without very much roofing experience, it would be much harder for you to spot any problems than a trained and experienced professional. A professional roofing contractor could find any leaks, roof membrane damage, and membrane deterioration. Your local roofing contractor can also give you advice and recommendations on how you can improve the safety, longevity and durability of your roofing system.

Think of a roof inspection as a preventative measure that could save you thousands of dollars in per year. A professional roof inspection can reveal structural weaknesses in your roof, deficiencies, or damage that can lead to much more expensive roof repairs if left unchecked. A roof inspection also includes a thorough check-up of your home’s ceilings and interior walls for possible water infiltration such as ceiling tile stains, incorrect roof flashing, excessive debris, and curb or pipe penetrations. A comprehensive roof inspection can catch membrane deterioration early and have it fixed, if possible.

Make your new year’s goal, getting your roof checked at least twice per year! Some warranties won’t be completed without a thorough roofing inspection by a reputable local roofing contractor. Roof penetrations and incorrect flashing could potentially void the manufacturer’s roof warranty. Deterioration and damage can lead to premature roof leaks and cause serious emergency situations or disruption to your property. Preventative action always pays off! Therefore, we strongly recommend that you make scheduling a professional roof inspection a New Year’s Resolution.

Keep An Eye On Your Gutters

It’s critical to keep your gutters in working order to allow water overflow to drain from your roofing system. You want to ensure that water flows away from your roof without pooling in corners. You can also check your gutters to find out if you have significant and threatening shingle or tile breakage as well. The role of gutters is to route rainwater away from your home. It can be difficult for homeowners to identify minor gutter issues before they become full-blown failures. Neglect leads to clogs, which can cause leaks in the gutters. These leaks typically form at the joints, at the areas where gutters lengths and downspout meet. These areas are often sealed using a sealant, which can get worn out due to weather exposure. Gutters will also tend to overflow if clogged, so cleaning them regularly at least twice a year is important. Holes from rust spots are yet another source of leaks and can develop from the smallest exposed metal surfaces.

Water pooling around your home’s foundation is the biggest risk you would face when neglecting your gutters. This weakens the ground that the foundation sits on, which could cause the house to settle inappropriately. Also, your home’s foundation is made of concrete and concrete absorbs water. Water pooling around the foundation due to faulty gutters can weaken the foundation, causing irreparable damage. The fascia boards that hold the gutters in place could get damaged as well. The exposed wood will begin to rot if soaked in water. Gutter hangers could come loose, necessitating a complete gutter replacement.

Replace Missing Shingles Or Tiles

If your home or business has loose or missing shingles or tiles, you may wind up facing much more than an aesthetic problem. With missing or damaged shingles or tiles, your roof is much less likely to remain weatherproof.

When shingles from your roof fall from their adhesive backing or nails give out, they leave the insulating and adhesive layers open to the elements. This exposure can cause roof leaks, structural damage, weatherproofing damage and dry rot. Even if the open patch of a roof is small, average amounts of rainfall are enough to soak the layers between the exposed area of your roof and the inside of your home. Unwanted wetness in your home will cause roof damage as well as weaken floorboards, soak the insulation, and let moisture into your foundation.

Over time, the water from roof leakage can weaken your home’s structural beams and foundation, causing much larger, permanent problems. If your support beams fail to provide support for the weight of your house, you may experience foundation cracking, roof caving, and wall breakage.

Dry and hot as well as frequently changing weather conditions will stretch, condense, and water down the weatherproofing and adhesive layers beneath your roof tile. After these layers are exposed to dry air and direct sunlight due to missing shingles, they will lose their protective properties.

In hot weather areas, unprotected parts of your roof will experience dry, scorching air throughout the entire day. The air saps the moisture from places that need oil and moisture to function properly, causing them to expand without pliability. They will crack and weaken, leaving them vulnerable to breakage. These problems can also occur in combination. When they do, small problems with over-dryness or excessive moisture can cause much larger problems for the entirety of your house.

Since residential and commercial roofs in the region have to put with so much constantly changing weather, the cause of slipped, broken, and missing roof tiles or shingles can be one of a combination of the following:

Wind – Even if your roof is built with consideration for wind damage, strong, gusting winds can still pull shingles from their place if the come with enough force.
Trauma- Unusual weather events such as hail, rainstorms, or blizzards can pull tiles from their place. Tiles will slowly weaken and break from too much impact.
Dryness- Most types of roofing require moisture to stay weatherproof and secure. Droughts and severely hot weather will pull that necessary moisture from the tiles.
Weakening- Underlayment and sheathing underneath your tiles will start to give in to the elements over time. This allows your shingles to slip and opens them up to damage.

Consider Roof Cleaning

Cleaning your roof not only helps to please the eye, but it also helps in keeping it in efficient working order. Eliminating leaf and debris buildup can reduce the risk of mold and mildew that can seriously threaten the functionality of your roofing system.

Roof cleaning is commonly overlooked, however, when the siding of your home is dirty or the paint is peeling, it becomes an obvious sign that it is time for maintenance. However, the roof of your home tends to be a bit more out of the line of sight. As they say— “Out of sight, out of mind”. What many homeowners fail to consider is that a roof that is not properly cleaned and maintained can lead to damage which will shorten the lifespan of perhaps the most important protective feature of your home.

Your roof is exposed to the elements all day, every day. Dirt and debris will collect on it. Natural rainfall is typically enough to wash off the appearance of most superficial dirt. However, the dark stains and green areas that appear on your roof are caused by other natural elements. Some of these elements are algae, lichens, and moss.

If you have ever noticed any black stains on your roof, these stains are a growth called algae. Algae feed off both asphalt and limestone roofing in moist, cool and shaded areas of your roof. When there is minimal light, algae forms a blue-green color. The more shaded areas of the roof are more likely to have this algae, which can also harbor various types of molds. This explains why some roofs are stained only on one side. These algae spores are transported by wind or animals and can quickly spread from rooftop to rooftop in neighborhoods of single-family homes, townhomes, apartments and commercial complexes.

Lichens are essentially a combination of algae and fungus. Lichens are a fungus that grows along with algae. These plant-like organisms from a branching growth of root-like tentacles that penetrate deep into the shingle’s base for nourishment. Lichens are tough to remove from the roof and can reappear from humidity and rain.

Unlike algae and lichens, moss is an actual plant. Moss has a shallow root system and requires a lot of moisture to survive. Areas with less sunlight remain damp longer. Overhanging tree branches not only provide more shade, but they also drop debris that serves as a food source for moss. Like algae, moss spores are often transferred by wind or animals and can easily spread throughout neighborhoods.

The staining and growth patches caused by algae, fungi and moss can damage your roof through shingle deterioration and wood rot. Both lead to expensive repairs and can shorten the life of your roof. A thorough, professional roof cleaning can help minimize or reverse this damage.

Use these top roofing tips to get the year started right. Happy New Year from the Infinite Roofing team.

Safety Tips for Christmas Decorations on Your Roof

December 16, 2019 by Infinite Roofing Leave a Comment

The very best of holidays to you and yours! Infinite Roofing, as your local roofing contractors, want you and your family to be safe and sound this year and we offer this disclaimer: No one should try to attempt hanging Christmas lights when snow or ice is visible on the ground or on the roof, or during wet weather conditions.

Homeowners should follow all local roofing and safety codes, and ensure their own safety whenever they go up on a rooftop this year. We strongly advise that no homeowner should stand or walk on a roof without taking the proper precautions. If you really have to walk and stand on the roof this Christmas, take care to avoid damaging to your roof and shingles. We recommend that you always have someone assist you during the entire installation process, even just to keep a watchful eye.

The holiday is fast approaching and people are getting into the Christmas spirit, which means many Capital Region homeowners are thinking about all those amazing lights and eye-catching decorations. Fantastic, large-scale displays featuring holiday lights and decorations are more popular now than ever before. Neighborhoods are lighting up with outdoor lights, from yard displays to festooned trees, to lights all over the house exterior. However, please remember that if installed incorrectly, these electric lights and decorations can also be dangerous and it is important to address any safety issues so that your decorations are able to hold up during the extreme local winter conditions we may receive.

When dealing with your holiday decorations, it is very important that you set everything up in a way that does not damage your roof and put you or anyone else in harm’s way. Rooftop holiday decorations and lights can add a special touch to your roof. However, installing these decorations, especially electric lights, and moving apparatus can be very dangerous.

Roof Safety

Before you start any roof lighting projects, any experienced local roofing contractor will remind you to always put safety first. No matter what your roof safety plan is, it’s important to have someone on hand while you work. They can manage your tools and hand you supplies and decorations so that you’re completely focused on the task at hand. They can help you use the ladder safely by holding the ladder to steady it. Unless you are decorating the chimney or the ridge at the top of your roof, you really should not need to walk on your roof, which can be very dangerous and needs some knowledge as well as additional safety equipment. Great displays are ones people see from the street level, so it’s not really necessary to go above the eave line to have a beautifully decorated roof.

If you do have to step on any portion of the roof surface, or even just in general for working from a ladder, wear sturdy gym shoes that have a good grip and are easy on the roof surface. You really don’t want to have to call in your local roofing contractors prematurely in the New Year, but even worse would be if you or a loved one ended up requiring medical attention for not taking appropriate precautions.

Check your Holiday Lights and Equipment

Another top Infinite Roofing tip for the best roofing safety practice with your Christmas lights is to make sure that all your lighting strands are in good working order and that you have enough of them to cover the area you plan to illuminate. Of course, you must check and make sure they are all rated for outdoor use. Draw up a thorough plan to best install any holiday lights you have on hand. Lay the strands of lights out in your home a few days before you plan to install them. Look for any frayed wires that could be a fire hazard. Now’s a good time to replace broken or missing strands of bulbs. Promptly get rid of any strands that aren’t up to par, it’s not worth the risk!

Protect your Roof & Shingles

Before installing your lights on the roof, be sure to stock up on plastic clips or hooks on hand for attaching the lights to the eaves or gutters. Plastic clips have a far less damaging effect on your roof compared to nails or metal hooks. Having outdoor extension cords where you need them to be is important and makes it easier for you to get everything lit up when it’s time. You can attach the light strands to shingles, eaves or gutters. One really important thing is to not hang anything heavy along with the lights because this can cause damage to the components of your roof. If you find extremely loose gutters or fixtures, get them repaired before hanging lights on them, as they may further loosen or fall down during harsh winter weather, taking all your decorations with them. Using nails that would put a hole in your roof is a huge no! The structure of your roof is vital and any little hole can eventually lead to a much larger hole and allow moisture to seep into the roof. Plastic lighting clips are very simple and inexpensive. Most hardware stores carry these clips around their lighting and tree displays. You can also use plastic zip ties which will not harm your roof fixtures. If you plan to put heavy displays on the roof be sure they are secured with something that doesn’t pierce the roof so they don’t fall down and damage the roof in a high wind.

Types of Christmas Light Roof Clips & Roof Fasteners

When you’re hanging Christmas lights on a roof, you shouldn’t use any fasteners that would be able to puncture the shingle or any other part of the roof, such as nails, staples or screws. Even small holes in the shingles can create leaks. Small holes in gutters may allow water to leak where it shouldn’t and holes in the fascia board may cause it to rot. This could later cause you to require a roof repair or even a replacement. No one wants to spend their Christmas money on a whole new roof when using fasteners that will not create holes could have been used instead. If you’re unfamiliar with roofs, now is a good time for you to learn about all the parts of your roof and the roof edge before you put up your Christmas lights.

So, if you shouldn’t puncture holes in the shingles, how do you secure Christmas lights to your roof? The solution is to use specialized plastic clips that can hug the gutters and they won’t leave a lasting mark. By using these clips you can have a huge display, with as many fasteners as you need, without worrying about leaving a bunch of holes in your roof.

On areas of the roof that do not have gutters, attach the clips to the drip edge or the shingles, but be careful to avoid lifting the shingles in a way that breaks the sealant bond to the shingle below it. Avoid puncturing holes in your shingles or siding. Alternatively, you can use adhesive strips to attach the clips to the vertical face of your home. Just be sure you don’t puncture the surface!

How Can I Hang Christmas Lights Without Making Holes Step by Step

Locate an electrical outlet. Plan to run heavy-duty extension cords on a working 120-volt electrical outlet protected by a ground-fault circuit breaker. Ideally, you should use a switch-controlled outlet, or plug the lights into an automatic timer. Both the outlet’s circuit and the timer must be rated to handle the combined amperes of all light strings that will be connected. Do not use an indoor timer outdoors.
Measure the lengths. Using a long measuring tape, measure the length of your house along the ground. Also, measure its height and the height of any bushes or trees you intend to light. Then measure the lengths of the light strings you will need to outline doors or windows. Figure out the number of 50-foot light strings it will take for all of these measurements.
Test the lights. Before you plug them in, visually inspect the light string, looking for broken or missing bulbs and worn or defective wiring. If you discover faulty wires, replace the string entirely as this could present a fire hazard. If any bulbs are broken or missing, you should definitely replace them.

To extract a broken bulb, wear gloves and use long-nose pliers. Once a light string is complete, plug it in and check for burnt-out bulbs. Unplug the string before replacing faulty bulbs and then retest it to be sure all the lights work. If the string doesn’t work at all, check it for a blown fuse, per the manufacturer’s directions. If the fuse has blown, replace it; if it blows again, replace the entire string.

Set up a ladder. If your home’s eaves are low, you may be able to use a stepladder; otherwise, plan to use an extension ladder. Place it firmly on flat ground and, extending it well above the eaves, lean it against the eaves at an angle that will be comfortable and safe to climb; neither too steep nor too flat. If you must lean the ladder against the gutter, place a short piece of 2 by 4 inside the gutter to reinforce it.
Hang the lights along the eaves. Your objective is to hang lights as easily and safely as possible without marring your home’s trim or walls. For attaching lights along gutters or the roof, use plastic clips made for the job. These clips grip shingles or gutters and have a lower hook that holds a light strand or extension cord.
Attach the lights to the trim. For attaching lights to window trim and similar vertical surfaces, use rope clips, adhesive or nail-on plastic string light clips; readily available online or at home improvement centers. Space them about 12 inches apart or as recommended. Do not use staples or nails to hang light strings they can pierce or wear away the protective insulation, creating a serious electrical hazard.

How do you hang Christmas lights without a ladder?

The way that you would hang Christmas lights without a ladder is by taking a clip and putting your wire inside, then popping the clip in the pincher end of the pole. Raise it up to the edge of your roof or you can pop the clip in first and then pick up the wire. Then you would slide the clip under the shingles. Pull the release trigger and very gently remove them from the clip. Now, there is a little bit of a difference when it comes to hanging lights on your gutters. Looking at the instructions that come with the pole to see the best way to hang your lights is also a really good idea.

As local roofing contractors, we know that hundreds of roofing accidents occur from hanging Christmas lights and decorations each and every year. We hear all the horror stories! To avoid looking like the guy from Christmas with the Kranks where Tim Allen is stuck hanging from his rooftop, always have someone with you ready to assist. Never hang lights if there is visible snow or ice on the ground or roof, or during wet weather conditions— we do not want any slip and falls! Good home improvement stores carry accessories for personal ladder safety as well as accessories to prevent the ladder from damaging your home. When taking down the lights, you shouldn’t just pull on the string. While it saves you time, it may pull down your gutters and otherwise damage your asphalt shingled roof. Instead, take down your lights the same way you put them up; carefully, safely and one clip at a time. Be conscious about how you wrap and pack away your light strings. If they twist, they may become damaged or get kinks and look odd next year. Especially if you use clips that hook to the line instead of to the bulb.

Stay safe! Merry Christmas and a very Happy New Year from your local roofing contractors at Infinite Roofing!

Roof Decking: Rotting & Corrosion

July 18, 2019 by Infinite Roofing Leave a Comment

Owning a home is one of the most challenging, yet rewarding responsibilities a person can have. You get the chance to establish a sanctuary for you and your family that provides the protection and comfort you desire. However, this can all be put at risk when you begin to notice issues with your roof such as a couple of wet spots on your ceiling. This may be your first home and may have never even looked at a roof’s foundation before let alone knowing where to begin. You go up to your attic to investigate, and come upon a distinct musty smell of mold. Signs would point to a roof leak, and one of the main causes usually would be roof rotting or roof corrosion if you own a metal roof. What do you do? You may not be an expert in roof contracting, but that is why certified experts like us at Infinite Roofing are here to help you get back to living with the protection and comfort you deserve.

What is Roof Decking?

When talking about roof rotting, we are talking about the roof decking or sheathing of the home. The roof decking plays a pivotal role in determining the safety and structural integrity of your roof.

Roof decking is the foundation of your roofing system. It is the base layer that connects the roof to the home. The roof deck is placed between the structural components, such as the trusses and joists, and the insulation/weatherproofing layers. When it comes to your roof rotting, you want to take all the steps necessary to ensure the health of your

Roof Decking Materials

Roof deck materials come as 4 x 8 sheets in a variety of different material options. The most common type of roof deck material is plywood, which comes as either OSB (Oriented Strand Board) or CDX (C to D Exposed). Other roof decking materials include steel, concrete, and cement. The main determinant of the type of material you should use is based on the amount of weight that the roof deck will need to carry, plus the weight of air conditioning equipment, rain and snow. For most residential projects the common choice of roof deck materials are OSB or CDX plywood. For commercial projects, steel, concrete, and cement are more commonly found in the roof deck. These materials are definitely interchangeable depending on your project requirements, however for now let us focus on three main materials; OSB, CDX, and steel.

OSB Plywood

OSB (Oriented Strand Board) was originated in the late 1970s as an extended use of waferboards. It separates itself from other wood-scrap materials because the long strips of wood are placed strategically instead of randomly, hence the name “oriented” because the wood strips are oriented strategically to improve the strength qualities from the waferboard. OSB Plywood is made from heat-cured adhesives and rectangular-shaped wood strands that are arranged in cross-oriented layers. Because OSB uses small wood strands for production, it is considerably less expensive than standard plywood. When produced in large, continuous sheets, the OSB is a sold-panel of consistent quality with a few voids or gaps. OSB Plywood is more susceptible to absorbing moisture and swelling up than CDX, due to the release of compaction stress in OSB created during the pressing of wood chips into the panels. Swollen OSB will remain permanent, to a degree, causing leaks, increasing decay, and creating uplift of whatever materials lie above.

CDX Plywood

CDX (Class C to D Exposed) Plywood is the lowest class of plywood and is often used in the construction industry or as a base to create other materials. Plywood is made from thin layers of wood that are peeled from a spinning log, called veneers, that are cross-laminated and glued together with a hot press. Throughout the thickness of the sheet, the grain of each layer is laid perpendicular to the adjacent layer. The final product is an odd number of layers so that the balance is maintained around the center. Since CDX is made from whole layers of logs as opposed to small strands, the plywood is much more consistent and has a less rough appearance than OSB. CDX is lighter than OSB, retains nails and screws better than OSB, and produces less swelling when exposed to water and will return to its normal thickness after drying. This feature alone is enough for roofing contractors to prefer using CDX Plywood over OSB for their roof sheathing.

Steel

Steel or Metal Roof Decks have been around since the 1930s/40s. The Steel Deck Institute (SDI) has been the biggest force in setting the standard when it comes to the design, manufacture, quality control and construction practices applied to cold-formed steel decking. The steel deck is roll-formed from structural quality sheet steel and is made to span over the roof joists or purlins to provide a flat surface to apply the weatherproof roofing. The variations in its thickness, shape, and depth can be used to meet the variety of loading requirements and spans. The steel deck’s versatility also allows for it to be used in more unusual configurations that may be sloped or curved. Steel decks are usually more costly than materials like plywood however, they provide increased longevity, durability, and a better strength-to-weight ratio backed by years of proven satisfaction in the roofing industry. Steel decks are more commonly used for flat roofing systems, which are typically used for commercial roofing projects.

How Can I Tell When My Roof Is Rotting/Corroding?

As a homeowner, you want to do anything that you can to keep your home safe from the elements of mother nature. Your first line of defense is your roof, so how can you tell when your front line is starting to deteriorate?

First things first, is it even safe for you to check your roof? We do not recommend grabbing a ladder and going on your roof to do an inspection. According to the American Association of Orthopaedic Surgeons, last year there were about 500,000 ladder-related injuries due mainly to homeowners trying to clean out their gutters or perform their own roof inspections/repairs. Our team of certified roofing contractors have specific equipment and years of experience in doing roof inspections safely and thoroughly and will provide a free, no-obligation estimate for any repairs or replacements needed.

With that being said, there still are some telltale signs that you as the homeowner can check for yourself to see if an estimate would be needed.

Roof Rotting

Here is a list of signs that your roof deck may be damaged or rotting:

Shingles curling, cracking, or buckling
Missing shingles
Holes in the roof
Mold or mildew in the attic
Spongy feel when walking on the roof
Granular wear to shingles
Damage around chimneys, pipes, and other penetrations to the structure.
Wet spots on your ceiling
Sudden increase in electric bill

There are some DIY inspections that you as a homeowner can do to find the beginning signs of roof deck damage.

Attic Inspection: Carefully make your way up to your attic and check for any signs of rotting wood. Do you see any signs of staining or moisture on any of the plywood or insulation? Can you feel any dampness in the wood? Is there a musty mold smell lingering? Can you find any holes, possibly made by a new furry neighbor? Is your attic fan and ventilation system free of dust & debris and circulating the air properly?
Ground Check: You can take a trip outside and stand in front of your home to view your roof from the outside. Are there signs of curling or missing shingles? Can you notice any sagging or structural integrity issues with your roof?
Research Roof’s Age: Severe weather or a poor ventilation system can decrease the life expectancy of your roof. If your roof is more than 20 years old, it’s a good idea to reach out for a professional roof inspection.

Roof Deck Corrosion

Roof deck corrosion occurs when using steel for your roof deck construction and has been exposed to water either from a hole created from severe weather or poor roof or insulation installation causing gaps between the roofing and insulation and allowing for water exposure.

WARNING: We do not recommend walking on a damaged metal roof structure. Corroding metal roof decking can cause structural instability which can lead to the roof collapsing if too much weight is put on the structure, leading to injury. Please refrain from having work done on units on your roof if you suspect instability in your roofing structure.

Some visible signs include:

Visible rusting in roof deck
Pieces of roof deck missing or falling from structure
Wet or damp insulation
Holes/leaks in roof

If you believe that your metal roof decking may be damaged, immediately have a professional roofing contractor, e.g. Infinite Roofing, come do a thorough and safe inspection of the roof.

So What Do I Do? Repair or Replace?

Rotted or corroded roof decks, whether made of plywood, steel or any other material, cannot be repaired and must be replaced. Contact your local certified roofing contractors and set up an appointment to have the damaged roof deck to be replaced.

Our professional roofing contractors here at Infinite Roofing would replace the rotted roof decking, along with the top of the line GAF and Versico accessory products to help prevent further roof deck rotting or corroding such as:

Lifetime Roofing Shingles
Proper Attic Ventilation
Proper Roof Deck Protection
Ice & Water Barriers
Starter Strip Shingles
Ridge Cap Shingles

Adding these top of the line products will increase the longevity and durability of your roof decking. When it comes to protecting the welfare of your home and family, you want to have the best certified roofing contractors and products out there. Here at Infinite Roofing, that is exactly what we intend to provide for you.

Is your roof leaking? Could the ridge vent be the problem?

June 21, 2019 by Infinite Roofing Leave a Comment

Do you have a roof leak and can’t figure out what the problem may be? Don’t assume that a faulty roof or the shingles may be the problem and that you may need a full roof replacement. Faulty ridge vents can contribute to the problem and can lead to moisture issues. Fixing a leak quickly is important because if not fixed it can cause more problems down the line.

What are ridge vents?

You may wonder what exactly is a ridge vent and where does it fall in the equation of a roof leaking?

Ridge vents are critical to the attics health, they are a part of the attics ventilation system and helps circulate the air. They also usher moisture (in winter and summer) and hot air (during the summer) that would otherwise lead to damage. It is a metal capping that allows hot air to escape from the attic, the ventilation allows the attic to stay dry, free from any moisture and also prevents it from damaging your insulation. When getting a roof installation a ridge vent will be the last thing that will be placed on the structure and for that reason, a ridge vent leak can occur. Many time the fasteners that are used for the ridge vent aren’t secured properly

Inspect the Attic

Go up to the attic during daylight. Keep the lights off and look up at the roof to see if there is any light coming through. Diffused light is normal, but a beam of light may be the cause of a leak. Then, use a flashlight to examine the ridge vent. Look for moisture or water stains. Water stains may be from an old leak.

Another good time to inspect the attic is when it is raining. Be sure to notice where the water is coming from, because it may be channeled from another area on the roof before dripping down into the attic.

Air Circulation Problems

If you don’t see any leaks, you may have a one-time problem with rain or snow being blown in by heavy winds. Another problem can be a lack of ventilation in the attic. If the air is not circulated, you may get a problem with condensation, which mimics a roof leak.

Most Albany roofing contractor recommends that a roof should be inspected at least ones a year to prevent a ridge vent problem from creating bigger trouble and more damage than it would if it was to be. A strong gust of wind can pop up the ridge vent cap and if not taken care of immediately as rain, snow and even ice dams can cause your roof to leak. The process if inspecting the roof can be done by the homeowner or a professional

Repairing leaking ridge vents

Avoiding problems with ridge vents leak is easy when you schedule an annual roof inspection. During the evaluation, the Albany roofing contractor will not only assess the condition of the ridge vents, but he will also identify issues with shingle wear, damaged flashing and more.

If you feel that crawling around on your roof is a risky and perhaps dangerous job; you are exactly right. There are professionals that will inspect your roof and look for a ridge vent leak for only a minimal cost. These professionals will inspect various other common problems that may occur, as well.

Let the professionals do their job and call Infinite Roofing for an inspection to make sure that there is no ridge vent problem with your roof!

DIY method to remove Moss and Lichen With Vinegar

June 17, 2019 by Infinite Roofing 18 Comments

Damp conditions are perfect for mosses and lichens to grow, lichen consists of a fungus and photosynthesizing plant, while moss itself is a plant. When materials like leaves collect on your roof, a perfect bed is formed for moss and lichens to grow. People try finding ways to remove moss and lichens themselves without having to hire roofing contractors and there are ways to take care of that problem yourself and also do it in an environmentally friendly way. You can remove moss and lichens from your roof by using vinegar as an environmentally friendly weed killer. Roof cleaning is an important aspect of having your house look new and not aged. Algae and moss on roofs adds years to the look of your house, removal of algae will bring newly replaced roof look and make your house stand out.

Step 1

Ensure to clean up any organic matter on the roof such as leaves, twigs or other debris. Organic material is a perfect growing ground for moss and lichen, not only that it can also rot and possibly damage your roof.

Step 2

Use a push broom, or other sorts of stiff brush, to scrape away any stubborn mold or lichen patches still remaining. Begin with the top of the roof and work your way toward the eaves. For your safety stay well away from the edge of the roof.

Step 3

Use a tall ladder, and set it up next to the house. Get rid of any moss around the roof edges using the brush. Repeat this step and work your way around the house to make sure all sides are covered. If ever any step seems like they may be too dangerous for you to perform yourself, roofing companies always offer cleaning services and professional roofing contractors can always inspect your roof while cleaning.

Step 4

Take a bucket and pour distilled white vinegar into it. The vinegar should be labeled with its acetic acid strength, which shouldn’t be more than 5 percent. To help the vinegar cling to moss and lichens add a 1 oz. of dish soap, and finally pour the mixture into the spray bottle.

Step 5

Use the spray bottle and apply the vinegar to the moss and lichens on the roof, then get off the roof and apply the vinegar to the moss and lichens around the edge.

Step 6

This is where the waiting game begins, it generally takes a couple of days for the vinegar to kill off the moss and lichens.

Step 7

Use the brush that was used earlier to remove the dead lichens and moss.

Step 8

The final step is to clean the roof is to use a garden hose or sprayer to rinse off everything.

An option to consider when trying to avoid problems related to moss and algae on the roof would be to consider the GAF StainGuard technology. When your roof has run its life and it’s time to replace the roof, talk to your local Albany roofing contractors about the possibility of having the GAF Timberline shingles that have the stain guard technology, or the GAF Ultra shingles that have the StainGuard plus technology installed.

Blue-green algae, also known as Gloeocapsa magma, has spread throughout more than 80% of the U.S., leaving dark black stains wherever it grows, and making millions of perfectly good roofs, and the homes they protect look old before their time.

Many traditional algae-resistant shingles use a granule technology developed more than a quarter-century ago. There is a layer of algae-fighting copper in the granules that is released onto the roof when it’s wet. Granules get older as the roof ages, and it releases less and less copper, affecting and reducing the shingle’s algae resistance.

StainGuard Plus™ Time-Release technology from GAF releases algae-fighting copper more efficiently, over time, for long-lasting algae-fighting power.

Unlike the older layered technology, StainGuard Plus™ technology uses specially engineered capsules, that are infused throughout with thousands of copper microsites so copper remains within reach, ready to be activated in the battle against blue-green algae stains.

StainGuard Plus™ uses a time-release technology, its algae resistance so powerful, it comes with a 25-year ltd. warranty against blue-green algae discoloration.

Roofing companies offer GAF products with the warranties in Albany, we at Infinite Roofing and Construction pride ourselves for our GAF certification and the knowledge to sell you the right product, with the correct installation so you as a consumer can get all the benefits provided by the GAF StainGuard technology for the protection it guarantees for your roof.

Moss and lichen are an easy problem to solve, but why not prevent the problem altogether by getting the right material for your roof that would prevent the growth of moss and protect your roof throughout the years.

What are “Storm Chasers”?

June 3, 2019 by Infinite Roofing Leave a Comment

Your roof can suffer a great deal or damage when a big storm hits and your roof takes storm damage. Typically, this storm damage is covered by your homeowner’s insurance, which means you are more likely to take action to repair or replace your roof. “Storm Chasers” are fraudulent roofing contractors that know about the increased likelihood of roof repair in areas affected by large storms, and can rip off homeowners with poorly constructed roofing projects. Knowing how to identify these storm chasers can help you avoid falling for their corrupt tactics.

What is a storm chaser?

Roofing contractors who go to areas recently affected by storm damage, rain, hail or strong wind are called storm chasers. They use special programs to locate large storms and determine the value of affected homes. These roofing contractors have immense knowledge about insurance companies they use their knowledge to estimate the cost of a new roof. Local and reputable roofing companies are most likely overwhelmed and overbooked, and the “Storm Chasers” use that to their advantage and go door to door to notify residents that they have roofing services available. Typically, they will start by offering a free roof inspection.

Why are they unreliable?

Most storm chasers only do the bare minimum to replace a damaged roof. They will find the cheapest materials to quickly assemble a new roof, often leaving out important elements that a professional roofing company would take in consideration, and they fail to restore things back to their original condition. The roofs that are installed by them usually only have a lifespan of fewer than 10 years because they are installed using cheap material, whereas a professional roofing company using high-quality materials and techniques would leave you with a roof lasting 40 years with warranties to back up their install. Professional roofing companies have the certifications and licensing while storm chasers usually do not have the proper licensing or insurance to work on roofs.

In some cases, storm chasers do not replace the roof at all. Instead, they give a free inspection, quote a reasonable price and ask for upfront payment. Once they are paid, they move on to the next town without any intention of working on the roof.

What tactics do storm chasers use?

If you want to avoid being scammed by storm chasers do your research before handing over any money. Make sure that the contractors you hire to replace your roof or fix the storm damage have a reliable background and pay close attention to the approach they use. There are a few telltale signs that a contractor is a storm chaser.

1-They come directly to your home

The most obvious tell-tale sign for storm chaser is that they come directly to your door, Roofing companies don’t go out looking for work, especially after a big storm, they know that work would be coming to them as people will try to find reliable roofers in Albany to deal with their insurance agency and get the best repair or replacement possible. Storm chasers, on the other hand, move around to wherever the storms go, they cannot rely on the chances that people in need of roof repair will find them. Sometimes storm chasers go so far as to pretend they were sent by a company that previously worked on your roof. If this happens, ask for proof.

2-They want payment upfront.

No roofing company will ask for payment upfront before starting the job, When you pay storm chasers upfront, even if it is just a deposit, it is likely that it will be the last time you ever see them.

3-They offer to pay for the deductible.

How nice would it be to have your insurance deductible waived? Storm chasers think so, too. If a roofing contractor offers to pay for your deductible, they are probably a storm chaser. It is considered insurance fraud to allow a contractor to pay the deductible. If you let a roofing company pay your deductible, you will be the one responsible for committing the illegal act. Make sure you are familiar with your insurance policy and the laws regarding fraud to prevent yourself from falling into this trap.

4-They create damage that was not there before.

Because they are usually familiar with the insurance claim process, storm chasers sometimes create their own damage if the real damage is not sufficient. They may use golf balls, hammers or other hard, heavy objects to pound dents into your roof. Watch and listen carefully as contractors inspect your roof and have a camera or cell phone ready to catch them in the act if you are suspicious. Adding fake damage for the purpose of collecting insurance money can have serious consequences.

Educate yourself and your neighbors about the common signs of storm chasers to avoid being the victim of a roofing scheme. Check the Better Business Bureau if you are unsure of the legitimacy of a roofing contractor. This will tell you if the business is local and if complaints have been filed against it.

Infinite Roofing and Construction is proud to boast an A+ rating on the BBB. We are a local, trusted roofing company in Albany with over 20 years of experience. Getting a new roof is an expensive endeavor, so make sure you are getting it done right the first time by a company you can trust.

Do you really need 3 estimates for a roofing job?

May 29, 2019 by Infinite Roofing Leave a Comment

You’ll need to get as much information and knowledge about the process when looking to replace your roof. You need to weigh your options for roofing materials, their cost, and learn as much as you can about the local roofing companies that will be doing the work. In particular, your goal should be to find the best work for the best value.

Conventional wisdom, and also your insurance companies state and push that you should get three estimates from your local roofing companies and choose the median. Why? Supposedly, a drastically lower estimate may indicate cost-cutting measures that could result in shoddy workmanship, while the highest estimate could wind up costing you a pretty penny for average durability.

Meanwhile, if you’re replacing your roof due to an insurance claim, your insurance company may be stressing that you obtain at least three estimates. However, the three-estimate rule is not a hard-and-fast requirement for insurance claims, nor is it a necessity for your own decision-making process

So how many estimates do you really need?

The thought process behind requesting multiple estimates is solid. replacing a roof is a major undertaking that costs you a good deal of money and stands to make a lasting effect on your home’s weatherproofing, durability, and resale value for years to come. Of course, you want as much information as possible so you can feel comfortable proceeding. You also want to make sure the local roofing contractor you choose provides high-quality materials and high-quality installation and the best way to make that determination is to compare them to other local roofing companies that offer the same service.

However, do you really need three estimates? Not really. In this case, the “right” number of estimates depends completely on you. Get as many, or as few estimates as you need in order to feel comfortable with the roofing company you choose and their pricing.

Insurance companies are in no way required to get three estimates. All roofing contractors receive payment following a third-party system designed to set industry standard prices. Your insurance company will pay your area’s best roofers in Albany the exact same amount as it pays the worst roofers in Albany. Gather as many estimates as you feel comfortable with and choose the best company, just as you would if you were footing the bill on your own.

How do you go about choosing the best company? Ask these questions aside from the affordability factor to determine the best roofer in albany for your job.

Have they performed work in the area? Ask for references and addresses. There’s no better way to get a feel for a company’s customer service and workmanship than by speaking with former customers.

How experienced is the crew? It’s a good sign if your roofing company has been in business for decades and has great reviews. However, make sure to ask about the experience level of the particular crew that will be performing your work; a long-lasting company can easily hire a crop of newbies that may not have any more experience than you do.

How can I reach out during the process? Asking this question, in particular, gauges the company’s customer service. Their willingness to answer questions, guide you through the process, and remain available speaks to how smoothly the process will go on install day.

Ask about any certifications that the roofing company may have, having certifications backs up the work that is done by the company and it would guarantee that they have the best training necessary to be working on your roof.

There is no number of “right” estimates that you would need to get, go with what you think is suitable for you. Infinite Roofing can provide you with a free estimate for your insurance company with a detailed inspection of your roof. Our certifications, reviews and our highly trained crew will guarantee a happy and easy going roof installation.

A homeowners guide to protecting the exterior of their house during a roof installation!

May 24, 2019 by Infinite Roofing Leave a Comment

Sometimes during a conversation with the customer, it can be pretty obvious that they care about their garden and landscape. It’s these jobs you’ll know to take extra precautions with, but concerns about landscape don’t always come up in the conversation. Its always wise to maintain a clean job site, as it won’t cause problems post-install, and a clean work site is a safer site for your crew, the homeowners, and any neighbors or visitors.

When homeowners sign a contract with local roofing contractors, usually their main concern is that their roof installation is done properly. Unfortunately, the most common complaints about local roofing contractors is the occasional mess that is left behind after a job, and in some cases, the landscaping around the house can be damaged.

We at Infinite Roofing and Construction follow a “Never There” policy, as professional roofers in Albany we know that in the residential roofing business leaving the work property clean and undamaged is a priority for almost every homeowner, so we don’t take any chances. We always protect the landscaping, and we perform a magnetic sweep of the area after every workday to make sure all nails are picked up.

We also hang tarp on the eaves of the house to prevent felt paper from blowing back and damaging the siding. The bottoms of the tarp are tied down to a tree or trucks so they are tight and any debris slides away from the house. We will move the grills away to prevent any damage. Our customers appreciate this attention to detail around their home.

We take our “Never There” policy seriously, and even though with our roofing company you wouldn’t need to worry about your landscaping, extra care is never harmful, and It’s essential for you to protect the exterior of your home from any possible damage due to a roofing job.

Here are some important guidance for protecting your home exterior during roof installation and repair.

Secure any items hanging on the exterior portion of your home. Protect your at-risk items like patio furniture, potted plants, grills, and gardening tools with tarps and/or plywood, prior to starting roofing work.

You should relocate vehicles, falling within your home’s boundary to protect them from damage, and this includes vehicles parked in the driveway. Also, ensure to cover and protect valuables stored in your attic.

Prune back trees that are present close to the roof line, prior to beginning the roof installation process. This allows proper roof access to the local roofing contractors and prevents damage to the fresh roof.

Mow down your grass to the minimum height possible to prevent the nails from getting concealed, after falling into the long grass and ensure to shut your automatic sprinkler systems down, a day or two prior to beginning your installation to minimize any possible damage.

Secure your flowerbeds or landscaping surrounding your home by screening them with tarps or plastic by protecting them from dust and trash. You should also move out any hanging plants during your roof installation.

Damage to your pools, spas, and any nearby expensive equipment from debris and nails can be prevented. Cover the pools using a tarp and the spas with polypropylene to ensure your property’s protection before starting roof job.

Infinite Roofing and construction will make sure that any and all damage is prevented, and that the customer doesn’t worry about the aftermath of a roofing job, but little extra measures will only help and put your mind at an ease.